「松原伸缩门」不锈钢伸缩门按遥控没有反应是

作者:白城伸缩门定做   时间:2019-07-31 16:20




「松原伸缩门不锈钢伸缩门遥控没有反应是怎么回事


What happened to the stainless steel telescopic door of Songyuan telescopic door that did not respond by remote control?

 

不锈钢电动伸缩门,以威武挺拔的造型毅力于门前,成为企业的一道不可缺少的形象工程,更是企业财产的第一道防线,所谓门面,门面,是门 ,也是面。


Stainless steel electric telescopic doors, with the mighty and upright shape of perseverance in front of the door, become an indispensable image project of enterprises, but also the first line of defense of enterprise property, the so-called facade, facade, is the door, is also the face.



松原不锈钢伸缩门厂家
 


所以,企业在选在「松原伸缩门」电动伸缩门的时候,都要从多个方面考量,价格,质量,材质,服务都是您选择供货商的重要因素。


Therefore, when choosing "Songyuan Telescopic Door" electric telescopic door, enterprises should consider from many aspects, price, quality, material and service are all important factors for you to choose suppliers.


今天,「松原伸缩门」宏创门业为您分享一些关于伸缩门使用过程中的常见故障处理方式,主要针对控制系统。


Today, Matsuhara Telescopic Door Hongchuang Door Co., Ltd. shares with you some common troubleshooting methods for telescopic doors in use, mainly for control systems.


「松原伸缩门」不锈钢伸缩门按遥控没有反应是怎么回事


What happened to the stainless steel telescopic door of Songyuan telescopic door that did not respond by remote control?


白城铝合金伸缩门


一、按摇控器时,该门无反应,应如何办?


1. When the remote controller is pressed, the door does not respond. What should be done?


1. 检查是否对控制系统通电,若无,请通电;


1. Check whether the control system is electrified, if not, please electrify.


2. 检查摇控手柄背面标签所示遥控编码与遥控接收器部分背面标签所示摇控编码是否一致,若不一致,则查找统一编码或请专科维修员重新编码;


2. Check whether the remote control code shown in the back label of the remote control handle is consistent with that shown in the back label of the remote control receiver. If not, find the unified code or ask the specialist repairman to re-code.


3. 电路本身问题,如虚焊,漏焊等,判断方法;


3. Circuit problems, such as virtual welding, leak welding and so on, judgment methods;


4. 在通电状态下按动遥控器开,关,停按键后,听机头内功能电路继电器有无响声,并观察功能电路内指示灯是否亮,如果没有任何反应,请先更换门排线(连接接线盒与功能电路之间线)或检查是否有接反可能,如果没有,请找专科人士检修或更换功能电路;


4. When the remote controller is on, off and off, listen to the sound of the functional circuit relay in the head, and observe whether the indicator light in the functional circuit is on. If there is no response, please change the door arrangement (connecting the junction box and the functional circuit) or check if there is any possibility of connection. If not, please find out. Specialists overhaul or replace functional circuits;


白城伸缩门安装
 

二、门关不拢,即在正常关门进,发现倒退现象


Second, the door is not closed, that is, when the door is closed normally, the phenomenon of retrogression is found.


1. 限位磁铁没有正确安装,请参照说明书再次安装;


1. Limiting magnet is not installed correctly, please refer to the instructions for reinstallation;


2. 红外线防碰距离过远,请在机头内功能电路中将红外线防碰距离调节旋钮,将距离调短;


2. Infrared anti-collision distance is too far. Please adjust the knob of infrared anti-collision distance in the functional circuit of the nose to shorten the distance.


3. 防碰装置坏,调节距离失灵,更换功能电路或请专科人士检修;


3. Failure of anti-collision device, failure of adjusting distance, replacement of functional circuit or invitation of specialists to repair;